Why Is Water Leaking Through the Ceiling

Are you noticing wet spots or water stains on your downstairs ceiling after someone showers upstairs? Ceiling leaks caused by a leaky shower are a common problem that can lead to serious damage if left untreated. From mold growth to wood rot, even a small shower leak can cause significant water damage to your home.

water drops coming from bathroom ceiling

Common Causes of Ceiling Leaks After a Shower:

Leaking Water Pipes – Broken or loose pipes behind the walls can lead to water dripping down and damaging your ceiling.
Damaged Bathroom Tiles – Cracked or loose bathroom tiles allow water to seep through, causing leaks and damage to your downstairs ceiling.
Faulty Shower Faucet – A dripping faucet or showerhead can waste gallons of water, often leading to leaks inside the walls.
Clogged Shower Drain – A clogged drain can cause water to overflow, resulting in a ceiling leak beneath the bathroom.
Leaking Drain Gasket – The rubber gasket under your shower drain can wear out over time, leading to water leakage.
How Plumbers Fix Leaky Showers: When you call a professional plumber, they’ll start by identifying the source of the leak. Common fixes include tightening pipe connections, resealing shower drains, and repairing damaged tiles. A plumber may also remove any clogs in the shower drain using a snake tool, and it is recommended that damaged drywall or tile be replaced if necessary.


Shower Leak FAQs:

Will a wet ceiling dry on its own? It might, but it can lead to mold growth if not addressed quickly.
How can I prevent further damage? Improving airflow, using a dehumidifier, and drying the area with towels can help. However, it’s crucial to fix the source of the leak to prevent recurring issues.
Stop Ceiling Leaks for Good: If you’re still unsure about the cause of your ceiling leak, it’s time to call a professional plumber. An experienced plumber can quickly diagnose and fix the leak, saving you from costly water damage repairs in the future.

For fast and reliable service, contact Charlotte Plumbing Repair today and stop that ceiling leak for good!

Why You Shouldn’t Pour Cooking Grease Down the Drain




2/2





The Essential Guide to Maintaining Your Water Heater for Longevity and Efficiency

Water heaters are essential appliances in our homes, providing hot water for showers, dishwashing, laundry, and more. However, like any other appliance, they require regular maintenance to function efficiently and extend their lifespan. In this blog post, we’ll explore the key steps you can take to maintain your water heater, ensuring it runs smoothly for years to come.

#### 1. **Regularly Inspect and Flush the Tank**

One of the most important maintenance tasks for a water heater is to regularly inspect and flush the tank. Over time, sediment and mineral deposits can accumulate at the bottom of the tank, reducing efficiency and potentially causing damage. To prevent this:

– **Turn off the water heater:** For electric models, switch off the power at the circuit breaker. For gas models, turn the gas valve to the “pilot” position.
– **Connect a hose to the drain valve:** Place the other end of the hose in a floor drain or outside.
– **Drain the tank:** Open the drain valve and allow the tank to empty. This will help flush out any sediment.
– **Refill the tank:** Close the drain valve, remove the hose, and turn the cold water supply back on. Once the tank is full, turn the power or gas back on.

It’s recommended to flush your water heater at least once a year. If you live in an area with hard water, you may need to do this more frequently.

#### 2. **Check the Anode Rod**

The anode rod is a crucial component of your water heater, as it prevents corrosion by attracting corrosive elements in the water. Over time, the anode rod will corrode and need to be replaced to continue protecting your tank.

– **Locate the anode rod:** It’s typically at the top of the water heater.
– **Inspect the rod:** If it’s less than half an inch thick or coated in calcium, it’s time to replace it.
– **Replace the rod if necessary:** Simply unscrew the old rod and screw in a new one. Ensure the new rod is made of magnesium or aluminum for optimal performance.

Check the anode rod every one to three years, depending on your water quality.

#### 3. **Test the Pressure Relief Valve**

The pressure relief valve is a safety feature that prevents your water heater from over-pressurizing. If this valve isn’t working correctly, your tank could be at risk of bursting. To test the valve:

– **Locate the valve:** It’s usually on the top or side of the water heater.
– **Lift the lever:** Water should come out of the overflow pipe. If no water comes out or the valve is leaking, it needs to be replaced.

Test the pressure relief valve at least once a year to ensure it’s functioning correctly.

#### 4. **Insulate the Heater and Pipes**

Insulating your water heater and the surrounding pipes can help maintain the water temperature, reduce energy usage, and prevent the pipes from freezing during colder months.

– **Wrap the heater:** Use an insulating blanket around the tank, but make sure not to cover the top, bottom, or thermostat.
– **Insulate the pipes:** Apply foam insulation to the first few feet of the hot and cold water pipes connected to the heater.

This simple step can lead to significant energy savings and prolong the life of your water heater.

#### 5. **Set the Temperature to a Safe Level**

Setting your water heater’s temperature to a safe and efficient level is crucial for both safety and energy conservation. The recommended setting is around 120°F (49°C).

– **Lower the temperature:** If the water is too hot, it can lead to scalding and increase energy consumption.
– **Increase the temperature:** If you notice the water isn’t hot enough, you may need to raise the temperature slightly.

Check your water heater’s temperature settings periodically, especially if you have young children or elderly family members in the home.

#### 6. **Schedule Professional Maintenance**

While many maintenance tasks can be done on your own, it’s important to have your water heater inspected by a professional plumber every few years. They can perform a thorough check, identify potential issues, and ensure all components are in good working order.

#### **Conclusion**

Regular maintenance of your water heater is essential for ensuring its efficiency, longevity, and safety. By following the steps outlined above, you can keep your water heater running smoothly, reduce energy costs, and avoid costly repairs. A little effort goes a long way in maintaining this vital appliance, allowing you to enjoy hot water whenever you need it.

linkhttps://ebusinesspages.com/Charlotte-Plumbing-Repair_eo4n8.co’>Plumbing Drains and Sewer Consultants in Charlotte

Why Every Real Estate agent Needs To Know A Charlotte Plumber

Being a real estate agent can be a tough job. There’s a lot of regulations to follow, it can take weeks or months to sell a property, and if anything goes wrong, you’re the first person that gets the angry calls.

What does being a real estate agent in Charlotte have to do with knowing a plumber?

Quite a lot, actually. There are a few reasons why every real estate agent working in Charlotte, NC should make it a point to get to know a plumber from the area:

To Thoroughly Vet a Structure’s Plumbing
The first, and most obvious, reason why a real estate agent should know a charlotte plumber is to get that plumber’s help in checking the condition of a structure’s pipes and plumbing.

While Charlotte isn’t too close to the San Andreas fault, home plumbing systems can still be affected by distant earthquakes. Add to this the aging pipelines in most homes, and the countless other potential causes for damage to plumbing, and the need for a thorough inspection is clear.

By getting to know a plumber, Charlotte-based real estate agents can get thorough inspections of a structure’s plumbing systems prior to closing deals. This helps to limit liabilities in case of a plumbing failure since the buyer and seller will be aware of the situation.

To Fix Severe Plumbing Problems in a House Before the Sale
While some house sales are done with an “as is” stipulation regarding the condition of plumbing and other parts of the structure, most high-end real estate sales have some enforceable guarantees about the condition of the building.

In these high-value sales, it’s vital to prevent problems with the plumbing. Water damage from faulty pipes could require costly remediation—including tear-out and replacement of building materials.

Finding and fixing plumbing problems before the sale is often far less costly (and less headache-inducing) than dealing with a burst or leaking pipe after the fact.

To Protect the Good Name of Their Real Estate Agency
In the real estate business, your good name can make the difference between success and failure. Trust, once lost, is incredibly difficult to build back up.

By getting to know a Pineville plumber and having that plumber help you with plumbing issues in the properties you manage or sell, you can protect your real estate agency’s good name with buyers and sellers in Charlotte.

Preventing plumbing problems in your real estate deals is a key part of making sure deals go smoothly, and making yourself into the go-to real estate agent for Sacramento.

Learn more about common plumbing issues in Charlotte today!

Plumbing Contractor Huntersville, NC

How to Select a new Hot Water Heater for your home

waterheaterSelecting a water heater isn’t as easy as it used to be. Which is actually a great problem to have. Thanks to advances in technology, there are options for different budgets, energy sources, and household sizes. Modern water heaters are more efficient than older units, as well as longer lasting and easier to service. Let’s explore the different types of water heaters and find which one is best for your needs.

Tips for Buying a Water Heater
What may be best for your neighbors down the road isn’t necessarily best for you.

What energy source do you have?
Gas water heaters use propane or natural gas to heat the water. Electric water heaters are plugged into your home’s power supply. Research the cost of these utilities in your area, and see which one is the most affordable. Your existing utilities should guide your choice.
How much hot water do you need?
Hot water heaters come in different sizes and are rated to supply a certain amount of gallons per hour (GPH). To narrow down your decision, ask yourself how much hot water you or your family need. Do you use water at an average rate, or do you need a little extra?
How much space do you have?
Traditional and hybrid hot water heaters take up a lot of space, whereas tankless water heaters are compact. Ask yourself where the water heater will be installed and how much room you have.
Finding the Perfect Hot Water Heater
Let’s break down the pros and cons of gas and electric water heaters:

Gas Water Heaters: These have a higher up-front cost and must be vented outside, but they are more affordable to operate long-term. Gas water heaters also have a higher recovery rate, which is the time it takes to reheat the water after it is depleted.

Electric Water Heaters: These are easy to maintain and install, but they cost more to run and have a slower recovery rate than gas. Electric water heaters are a better option for homes that do not already use gas for other appliances.

Water Heater Size Considerations
The size of traditional hot water heater you need depends on the amount of people in your home. Most manufacturers provide guidelines for their units. A family of four should typically look at 50-gallon water heater or larger models.

Don’t just rely on the capacity of your water heater to determine if it is large enough. You should also look at the first-hour rating (FHR), which tells you how much water the unit will heat in a set amount of time. When you’re shopping for a new unit, ask about the FHR or consult this water heater size guide from the Department of Energy.

How to Choose a Tankless Hot Water Heater
Homeowners like tankless hot water heaters because they’re compact. They’re also more efficient, since they do not keep a tank of hot water ready to go. They can deliver an endless supply of hot water for even the longest-shower takers. They come in both electric and gas models, so simply choose the one that’s most compatible with your home and your utility bills.

How to Choose a Traditional Water Heater
Once you’ve landed on the correct size of a traditional water heater, as explained above, the next matter to decide is which energy source to use. If other appliances in your home already use propane or natural gas, it makes sense to buy a gas water heater. Otherwise, electric is a better option, since it can be expensive to install gas utilities for a water heater.

How to Choose a Hybrid Water Heater
Hybrid water heaters have a high up-front cost but are significantly more efficient than their counterparts. They have more moving parts, which can complicate maintenance, and they also require regular filter cleaning. They also require a drain, since they produce condensation. Finally, they require a lot of space. Hybrid water heaters are ideal for warmer climates or climate-controlled rooms, as they’re sensitive to extreme temperatures.

Point-of-Use Hot Water?
Point-of-use hot water systems deliver hot water to only one faucet or sink. They’re perfect for utility rooms, tiny homes, or areas of the home where running plumbing for hot water is cost prohibitive.

Professional Water Heater Installation
Once you’ve found the right water heater, give Charlotte Pluming Repair a call for water heater installation. We’ll take care of all the necessary installation procedures and adhere to local building codes to ensure a reliable and efficient installation. Give us a call at (704) 394-5252, or request a job estimate online.

If you’re looking for more advice about home appliances or need experts to help you maintain them, call Mr. Appliance. As part of Neighborly’s network of home service providers, Mr. Appliance is a brand you can trust for expert appliance maintenance and repair.

This blog is made available by Charlotte Pluming Repair , for educational purposes only to give the reader general information and a general understanding on the specific subject above. The blog should not be used as a substitute for a licensed plumbing professional in your state or region. Check with city and state laws before performing any household project.  Review us
Categories:
Plumbing
Plumbing Tips

Frozen pipes: How to prevent them

With temperatures expected to dip into single digits at night this week, don’t get caught with frozen pipes.

“To prevent frozen pipes, you need to find out where the air is getting into your house and seal it with insulation or caulking,” said Ernie Zimmerman of Charlotte Plumbing & repair.

It hasn’t been cold enough in the south for an extended period this winter for frozen pipes to be a problem, but that could be changing, with a high of 8 degrees forecast for Wednesday night.

Tips on preventing frozen pipes from American Water Company.

“Things are gonna happen, and probably will happen this week, since they’re calling for single digits,” said Ken Hartmoyer of Buchanan and Erb of Mecklunburg.

“It needs to be a high in the teens, with a good heavy wind,” Zimmerman said, for pipe to normally freeze.

Those who have had problems with freezing pipes in the past can leave faucets trickle, Zimmerman said.

But if you do this, let water slightly run, not just drip, said Dave Fessler, plumbing service manager at G. F. Bowman in Charlotte and Harrisburg. And don’t forget to remove the stopper from the sink, he adds.

“If you have cold spots on your wall, keep lavatory or kitchen sink doors open, which helps air circulate around the pipes,” Hartoyer advised.

“Never use a torch to try to thaw pipes,” Zimerman stressed, adding some homeowners have heat tape installed on pipes prone to freezing.

It’s not only homes with crawl spaces instead of basements that have frozen pipe problems, he said. “A lot of basements have a lot of air leakage,” Zimerman said, and that’s not only in older homes.

Having pipes in exterior walls makes them more prone to freezing. On an average winter day, it’s not a problem, but with frigid temps, there might not be enough insulation to keep them from freezing.

“Probably the only way to prevent it is to move them to an interior wall,” Zimerman said.

Chriss Weber of Plumbing and Heating in Huntersville said keeping cold wind away from pipes that tend to freeze is critical. Even newer houses might have pipes in outside walls, Weber said, since there are fewer inner walls with today’s open floor plans.

Heat tape can be installed to prevent pipes from freezing, but if your electricity goes off, that won’t be of much help, Fesler said.

Zimerman said he has machines to thaw metal pipes, but said they can’t be used with plastic pipes.

Another thing Zimerman said he stresses with customers is to have working carbon monoxide and smoke detectors. If you have a generator, never run it in the house, garage or basement.

To prevent furnace issues, have your furnace or boiler maintained annually, and don’t have combustible materials around the furnace or water heater, Zimerman said.

But if you haven’t had your furnace serviced, expect delays if you try to have it done this week.

“Everybody will be getting called at one time,” Hartmoer said, and breakdowns get priority over maintenance calls.

In extreme cold, Zimerman advises customers against turning the thermostat up and down. “It takes too long for the house to recover… It’s better to pick a temperature and let it there.”

“If you’re holding the temperature at 70 degrees, you should be OK,” Hartmoer said. And don’t forget to disconnect garden hoses from outside faucets, Hartmyer added.

Fesler urges caution in using electric space heaters in rooms with thermostats. If heat doesn’t kick on, susceptible pipes along walls or in basements could freeze. “Your heating system should run periodically so the water circulates,” Fesler said.

5 Plumbing Tips On Septic Tank Installation and Maintenance

5 Plumbing Tips On Septic Tank Installation and Maintenance

septic tank

To protect the health of the public from the dangers of inappropriate sewage disposal practices, North Carolina regulations have been adopted. The regulations are created to help insure that when a septic tank system is used, it will be constructed to meet North Carolina standards, of sufficient size to handle the likely waste load, and that the soil is suitable for saturation of sewage. These regulations require that a Local plumbing permit is needed to construct a septic tank system be obtained from the county code department. A septic tank system may not be covered with dirt until an inspection is made and approval is given by the county plumbing department.

Bear in mind that a septic tank cannot be safely installed on all home lots or building sites. Some lots or building sites are unacceptable because of the type of soil, terrain (too hilly, too low or wet, etc.), size, ground water, rock, or other factors which would obstruct with operation of the system. Die testing is required and in some cases sand mounds are constructed to accomplish the positioning of a septic tank.

Pro Tip #1 normal recommendation is to have the septic tank pumped (cleaned) out every 3-6 years. Some townships, citys or mobile home parks will have strict ordinance code regarding how often.

Pro Tip #2 Only residential waste and toilet tissue should be disposed of in a septic tank system. Keep all kitchen greases out of the plumbing system. Female personal hygiene items, cotton swabs, cigarette buds, hair from hair combs, paper towels, toys or mice from traps should never be flushed down the lavatory. Even a cotton swab can lodge sideways in a pipe and toilet paper will collect blocking the pipe going to the septic tank.

Pro Tip #3 Any leaks that develop in the plumbing system should be immediately corrected. A leaking faucet or toilet bowl, no matter how small the leak, will eventually result in complete penetration and failure of the drainage field.

Pro Tip #4 A septic tank system needs occasional cleaning or pumping out of the collected solids. If the solids are allowed to build up in the tank to a point that they begin to sepp out of the tank into the soil drainage system, the soil will soon become clogged with the solids, resulting in failure of the system. If this happens, costly repairs will have to be made before the system will again work properly. Raw sewage that comes to the top of the ground will indicate that the septic system has failed. It is unpleasant, unhealthy and usually a health violation that could lead to fines which only adds to the cost of a failed septic tank system.

Pro Tip #5 cars and other heavy vehicles should not be driven over the septic tank system. This causes extreme and actual structural damage to septic tank and tile drain field. A drawing of your septic tank plumbing can usually be obtained from your county code department to help you in knowing the location of all lines of the system. This can be helpful in case of problems with the septic system or when the tank is cleaned out.

PLUMBER TRADE SECRET: The recurrence of tank cleaning or pumping is hard to determine as it depends on many factors and ranges with different sizes families. The only sure way to determine the need for septic service is to open the tank lid periodically and inspect it to determine the addition of solids. This should provide a frame of safety, but remember the most proper way to determine the need for plumbing service is to inspect the tank contents once a yearly.

This article was brought to you by Charlotte Plumbing & Repair. At Charlotte,NC we specialize in all of your residential, commercial & emergency plumbing and drain cleaning needs. For more information please visit our website. We service all of mecklenburg metro!

How to Replace a Toilet

You might be amazed by the amount of money you can save on your next water bill by replacing your toilet with a new 1.6 gal per flush water saving unit. This is a job that can be completed by the general homeowner in an afternoon. With sufficient preparation, replacing a toilet is a fairly straight forward task.
Step 1:
Remove the new 1.6 toilet from its box and make sure there is no chips or scratches. Verify that all the parts are there. You will also need a wax ring which should come with the new toilet.

Step 2:
Turn off the water behind the toilet and flush the toilet to drain it. You will need to soak up as much as you can with a shop vac or rag and wring it into a pal. A genereal pair of rubber gloves will be helpful for the next step.

Step 3:
Separate the tank from the bowl by loosening the tank bolts. Take the tank off the bowl and discard it.

Step 4:
Unscrew the floor bolts that hold the base to the floor. Use a pair of pliers if the bolts are hard to move. Gently rock the toilet base to break the wax seal.

Step 5:
Lift the toilet straight up and set it on a piece of the box in order to protect the floor from any remaining water in the bowl or wax from the bottom. The cardboard will make it easier to move the toilet out of the way. It is a good idea to cover up the pipe with an old rag or plastic bag to prevent sewer gasses from escaping.

Step 6:
Remove the wax seal with a putty knife or paper towels. Apply the new wax seal around the toilet flange. first remember to remove the rag from the drain pipe.

Step 7:
Apply the new wax seal. Place the new toilet base over the floor bolts and center it over the wax seal. Tighten the bolts but not to tight and replace the caps. Attach the tank to the new base with the included hardware.

Step 8:
Connect a new water line to the toilet. Turn the water back on and wait for the tank to fill and check for leaks. You will need to flush a couple of times to fill the bowl with water.toilet

Why Does My Toilet Flush Slowly

Why Does My Toilet Flush Slowly
toilet
When a toilet flushes slowly there are really on two possible causes. The water is either slow going out through the trap way of the toilet bowl drain or, the water is too slow going from the tank to the bowl and the siphon of the water out the drain never occurs. The siphon is the process that rapidly clears the bowl and its contents with the gulping of air down the drain at the finish. When the water enters the bowl to slow the water just slowly runs through the toilet and doesn’t effectively remove the waste. Sometimes the waste just swirls around and only part of the waste leaves with each flush.

Siphon Flush

If you look at the side view of many toilet bowls you can see the outline of the trapway which sweeps up from the bowl then curves downward along the back of the bowl then continuing downward curves again towards the front of the bowl and goes out the outlet at the bottom between the two bolts that secure the bowl to the floor. The initial upward sweep and then the downward curve is what controls the water level in the bowl, and the trap way is a couple of inches in diameter. When the toilet is flushed a large volume of water should enter the bowl. Some toilets have a siphon jet which is a hole at the bottom of the bowl pointing into the trapway which water pours out of helping to push water into the trapway. The large volume of water should completely fill the trapway setting up a siphon, which sucks the water and waste out of the bowl ending with the air gulping into the trapway. If the water volume entering the trapway is insufficient to set up the siphon action the water just flows over the top of the trapway like water over a dam, this action is what results in the slow flush.

Bucket Test

When a toilet flushes slow, one of the first things you can do is the bucket test, which will test the function of the bowl. Get a pail and fill it with the amount of water that your toilet is designed to flush with. Quickly pour the water from the pail into the bowl, and see how the toilet flushes. If the toilet flushes poorly then you should suspect a clogged trapway and have the toilet augured to remove the clog. If the toilet flushes well then you know the flow of water from the tank to the bowl is the problem and you should direct your efforts in that direction.

How To Improve Flow From The Tank To The Bowl

When faced with a tank to bowl flow problem one of the first things I look at is if “in tank bowl cleaners” are being used. The bowl cleaners often clog the internal water passages of the toilet causing problems. I remove the bowl cleaner from the tank before doing anything else and in some cases this alone fixed the problem. I check the level of the water in the tank to make sure that the tank fills to the water level line on the tank or, the overflow tube. If there is no mark then 5/8” below the top of the overflow tube should be used. Check the flapper to make sure that it stays open long enough when flushing and does so consistently. Replace the flapper if there is any doubt. Make sure the fill valve has water going through the bowl refill tube attached to the overflow tube and the bowl is refilling to the proper level. Slowly pour water into the bowl to see if the water level in the bowl increases. If part of the water from the flush is devoted to filling the bowl to the proper level it can cause a weak flush. Finally take a piece of coat hanger wire into each of the holes under the rim of the toilet bowl and make sure that the siphon jet is clean as well. Frequently mineral deposits can clog the holes around the rim and the siphon jet causing water to flow slowly into the bowl. Checking these items on your toilet may restore good flushing to a slow flushing toilet. If these steps do not improve the flush then the toilet may require replacement.
http://411plumb.com/why-my-toilet-flushes-slowly

Steps on How to Fix a Leaky Faucet

Steps on How to Fix a Leaky Faucet
1dsfewr

Whether it’s the cause of water pooling under your sink, or the annoying dripping sound that keeps you up at night, a leaky faucet is a nuisance that could turn into a full-blown problem if not addressed properly. Fortunately, putting a stop to a leaky faucet, such as the compression faucet in your kitchen, can be surprisingly inexpensive and simple.

Tools you’ll need:

• Adjustable wrench; C wrench

• Phillips and/or flat-head screwdriver

• Penetrating oil, such as WD-40 or CRC

• Replacement washers and O-rings

Step 1: Don’t make a mess worse by transforming your broken faucet into Old Faithful. Before applying any wrench or screwdriver to your fixture, make sure your water supply is turned off, from the handles over the sink to the knobs underneath that control the water coming in from the main line.

Step 2: Remove any decorative parts of the handle knobs. A simple prying with a flat-head screwdriver will take care of that. Underneath each knob, there will be a screw that mounts the handle to the stem. Unscrew, then gently remove the handle with your flat-head. Using penetrating oil can assist in loosening it, allowing you to take the faucet handle off the stem.

Step 3: Use your wrench to loosen the packing nut. From there you should notice the stem. Remove that as well. Depending on the faucet, some stems pop right off, while others twist off from the valve. Check the removed parts for any damage.

Step 4: If everything is intact at this point, inspect the O-ring and washer inside the valve seat—they could be the reason for your leak. Remove the washer and put a replacement inside the seat.

It’s crucial to make sure your replacement washers and O-rings are an exact fit. If you are unsure about either, check the seat to see if the sides fit a cone-shaped or flat washer, and purchase the appropriate type. You may want to take the old O-ring to your local hardware store to verify the correct size. You can also buy a package including many different sizes of O-rings—sometimes it’s worth the extra few bucks.

Step 5: From here, carefully reassemble all the parts (in order of washer/O-ring, stem, packing nut, screw, and handle). Slowly and gently turn the knob to test the running water and check to see if you’ve licked that leak.

If, after all of your hard work, you notice the faucet is still dripping, then the cause may be corrosion in your valve seat. If not cleaned over time, it can produce leaks near the spout. Other potential problems are worn-out seals, loose parts, or, even worse, broken plumbing. If your troubleshooting leads to these areas, or if other sudden complications occur, then it may be time to call a professional Charlotte plumber.
source

Plumbing Tips To Prepare For Winter

water
Find out more on the subject of avoiding a few of the increasingly widespread plumbing inconveniences in the house. Many plumbing problems may be averted contingent upon the time of year. Chilly fall temperatures serve as a polite reminder that once winter arrives it may be unanticipated, often catching proprietors unprepared for plumbing inconveniences associated with extreme cold. Look here for valuable plumbing tips to keep your plumbing system running well during winter.

Turn off outdoor water hoses. If it is still connected, water inside the hoses can freeze and expand bringing about spouts and connecting pipes in your house to ice up and break down.

Ensure external taps are not leaking out or pouring out. Contact a plumbing contractor to take care of the crucial fixes before freezing temperatures arrive. Understand that once pipes ice up, water pressure grows and induces cracks – no matter whether pipe is composed of copper, plastic, or steel. Even a very little fracture might generate beyond 250 gallons of water in just one calendar day.

If your house has interior shut-off valves giving rise to outdoor spouts, disconnect them and drain water from lines.

Pad pipes in heatless vicinities, such as crawl or garages spaces. Position heating stripe or thermostat-controlled heat cables all over the pipes that are exposed and vulnerable to freezing.

Your water heater is working even harder at the time of wintertime months. Have a plumbing service professional flush it away and remove deposit buildup, which causes corrosion, shortens the length of life and reduces warming functionality.

Once departing from your residence for extended periods of time, shut off the major water regulator and take the water out by releasing open faucets at the highest and lowest places of the house.

Put into use the above mentioned helpful plumbing info and tips to increase the life span of your plumbing system in the course of wintry weather. It’s recommended to seek professional aid to winterize the plumbing system in your property.

Article Source: http://EzineArticles.com/5338347

Porch

” target=”_blank”>porch