Tag Archives: Belmont nc

plumbing, Plumber

Save Water This Summer

Clogged Drain,Commercial Plumbers,Commercial Plumbing Companies,drain cleaner,Drain Cleaning Services,Drain Cleaning, Emergency Plumbers,Emergency Plumbing, Drain Emergency Plumbing, And Drain Cleaning,Find A Local Plumber,Garbage Disposal,Home Plumbing,Licensed Plumbers, Pipe, Drain Cleaner,Plumbe,rPlumbers,Plumbing,Plumbing And Drain,Plumbing And Drain Cleaning,Plumbing Clogs,Plumbing Installation,Plumbing Repair,Plumbing Services Available,Plumbing Technician,Residential And Commercial Plumbing,Residential Plumbers,Sewer And Drain Services,Sewer Cleaning, Machinesewe,r drain cleaning,Sink Repairs,Toilet,Toilet Repairs,Water, Heater Water, Heater Repairs,

Tips That will Save Water, and Money
Water conservation should be a primary concern to all responsible people. Whether for drinking, cleaning, bathing, or gardening, when the warmer weather moves in our water usage usually rises significantly. That’s because there’s a lot of water-related chores and activities associated with the changes in the temperature outside.
Water resources aren’t as abundant as we may think. Sure, the world is mainly covered with oceans and lakes, but most of it isn’t fit for human consumption. Add the fact that major parts of the U.S. have experienced drought conditions for a number of years now and it’s safe to say every drop counts.
That being the case, consider some of the following tips for water conservation around the home this summer.
Home Water Conservation Tips

Yard Water SavingsWater Conservation

Hose: Instead of holding the garden hose and shooting a stream of water across the yard towards vegetation that needs to be fed try using the hose as a means of transporting water to plants. Then aim for the base of plants because that’s where water counts the most. Otherwise, it will fall in areas you do not intend to cultivate.
Drip irrigate: Even if you don’t live in an arid region like Austin, Texas, drip irrigation systems can be used to conserve water and hiring a plumber for installation isn’t necessary. The system consists of rubber tubing with holes that is connected on one end to an exterior spigot while the rest is carefully placed near plants and bushes. When the spigot is turned on small amounts of water exit the holes feeding nearby vegetation.
Morning watering: Feed the yard and garden in the early morning when water won’t evaporate quickly from the sun. Doing so will keep roots healthy throughout the day.
Kitchen Water Savings

Faucet regulator: Install a faucet regulator on your kitchen sink so water will never shoot out at full strength when initially turned on. If needed it could be adjusted for a steadier stream but in general will prevent a lot from flowing down the drain and being wasted.
Washing dishes: If necessary, let dishes soak in a tub to soften leftover crud and turn off water when scrubbing dishes. Only turn on the faucet to rinse.
Reuse: The kitchen presents many opportunities to reuse water for the garden or houseplants Some examples include water from boiling eggs, steaming veggies, and leftover water in the tea kettle.
Bathroom Water Savings

Toilet: Depending on the type of toilet, each pull of the handle can down several gallons of water, so don’t flush just for the sake of getting rid of a dirty tissue. A waste basket is for trash so only flush when necessary.
Brushing teeth: There’s no need to keep the water running when brushing teeth. Like washing dishes turn it on when you need to rinse. When left on the water is simply being wasted down the drain.
Shower: As you wait for the perfect temperature have a bucket handy to catch the first bit of water coming out of the shower head. It can then be reused in the garden, to wash floors, or to flush the toilet. Also, turn the shower off when soaping up and then back on again to rinse off. Doing so shouldn’t be uncomfortable in the warmer weather and can save gallons upon gallons of water.
You can always turn to the professional at Charlotte Plumbing & Repair Charlotte, NC 704-394-5252

plumbing, Plumber

Choising the right contractor

(FEE72D11769931286AE8E0A5012B5C90
A problem with the waterheaters in the in the home can lead to significant architectural troubles which explains why having a Charlotte Plumbing contractor on call at any time continues to be a good idea. While the hope is usually that one will never demand the expertise of a Concord Plumbing business, it is best to always be protected than remorseful. Plumbers undertake education and learning to deal with a range of residential plumbing related problems, from your leaking commode to the dripping faucet and a lot more. Do not assume that almost all plumbing contractors are identical, however, as there are many differences in terms of quality and also rates, so you want to ensure you get the best.

You should ask family and friends whom they prefer since they will give you an honest assessment of different businesses contractor. Without having any person in the area you really feel content asking, do some research online seeing as there are many great web pages where evaluations may be read prior to choosing any plumbing contractor. After you have narrowed your own list to a few trained professionals contractor, hunt for assurances and then simply call to obtain estimations. Even though a professional plumbing service will tell you they need to come out and evaluate the trouble right before you’ll get a final price, they ought to be ready to tell you how much you pay for the service call and details of that nature. Last but not least, ensure the plumbing technician has the appropriate bonding and also insurance protection thus, when a problem does indeed arise, the plumbing company is going to be responsible rather than you. You ought to be shielded too while you safeguard the investment in the house repairs. plumbers charlotte nc, plumber charlotte nc.

plumber charlotte nc, plumbers charlotte nc, Plumbing, plumbing, Plumber

What to do in a plumbing emergency

plumbers

Charlotte plumber sooner or later most homeowners will experience some type of plumbing emergency. Understanding what to do when a problem occurs will make the emergency much easier to deal with.

First, prepare yourself by locating the water shut-off valve, which is located next to your water meter. Once you have located your water meter, the valve next to it will be the water shut-off valve. By turning off the shut-off valve, you will stop all water from entering your home, thus minimizing water damage.

After you have shut-off the water supply, it is also a good idea to open all sink faucets to drain the water from the pipes to further minimize damage. Then, immediately call a plumber. Reputable, professional plumbers can usually send a technician out in a few hours. Follow any instructions given to you, while you wait for them to arrive.
It is also a good idea to use a mop, rags or paper towels to remove excess water, to help keeping water damage to a minimum.

In the case of overflowing toilets, you can shut-off the toilet water supply valve. This valve can usually be located between the bathroom floor and the toilet tank, on the water line supplying the toilet. If this is your plumbing problem, it is not necessary to shut-off the water to the entire home.

Clogged toilets and sink drains can sometimes be opened with a chemical drain opener. If this does not work, a plunger or snake can be tried to remove the clog. If these methods fail to open the clogged drain, you will need to call a plumber.

If it is a water heater problem, immediately shut the unit off. It is a good idea to locate the electrical shut-off switch beforehand. Also be sure to keep the telephone number of a licensed, professional plumber, with emergency services, handy. Handling a plumbing emergency can be made much easier, by following the steps above.

Are you facing a plumbing emergency in the Charlotte,Lake Norman area? Stop and call Charlotte Plumbing & Repair immediately at (704) 394-5252.

Leak Detection & Emergency Plumbing

plumbing, Plumber

5 kitchen counter upgrades You Can DIY

It’ll take some doing, but if your confident with your DIY skills you can make a kitchen counter upgrade with solid results. How? With step-by-step help from the pros at This Old House, of course. Here are our top projects to help you along. -Tabitha Sukhai, thisoldhouse.com

1. Install a Soapstone Countertop

best charlotte plumber

Too often the price of granite or engineered stone is out of reach of the average renovation budget. Not soapstone. This traditional kitchen topper is easy for a do-it-yourselfer to install, meaning you could save big on the labor, which usually accounts for half the cost. Available to be shipped nationwide from companies such as M. Teixiera Soapstone, where this counter came from, and starting at less than $25 per square foot, soapstone is a great, inexpensive DIY project.

470_2736507

Relative to other stones, soapstone is soft enough that it doesn’t require special tools to machine it. You likely already have what you need to cut and shape it: a circular saw, a jigsaw, a drill/driver, a grinder, and a sander. Here’s How to Install a Soapstone Counter in just an afternoon or two.

2. Install a Butcher-Block Countertop

470_2736510

Sleek granite and sharp stainless. It looks all luxe and modern-and maybe just a little bit, you know, cold. So what to do if you want more warmth in the heart of the home? Cozy things up with rich-looking butcher block. Not only are its well-oiled tones welcoming, it’s easy to install, as we demonstrate in How to Install a Butcher-Block Counter. Just order it to size, and then fasten it down. In hours you can turn a chilly steel-and-stone room into a charming cook’s corner.

3. Create Portable Workspace With a Butcher-Block Island

470_2736525

If you’re going for homey and cozy in your kitchen, skip the built-in cabinet-base island and instead make the central work area a furniture like table with a butcher-block counter. Because these thick wood-slab tops have their edge or end grain exposed, they are stronger than wood laid on the flat. That means they resist warping and nicks better than laminate and almost as well as stone.

With this durability comes an old-fashioned warmth. The trend for wood and furniture in the kitchen is in full swing, and butcher-block islands mimicking 19th-century worktables are perfect for toning down the coldness of stone counters and metal appliances in modern cook spaces. You can bring this classic aesthetic to your kitchen by constructing a prep island from easy-to-buy materials or choosing one of the dozens of styles available through retailers and furniture makers. Whichever path you choose, you’ll end up with an island that can be at the center of the cooking action and still take whatever you can dish out. Here’s How to Build a Butcher-Block Island in 5 steps.

470_2736526

Here’s another variation on this style, which combines iron threaded pipe and butcher block to create a kitchen center piece. Get the steps.

4. Other Kitchen-Counter Hacks: Remove Spots from Kitchen Countertops

470_2736528

“Stones are basically sponges,” says Fred M. Hueston, director of the National Training Center for Stone and Masonry Trades, in Longwood, Florida. He’s working in a kitchen, mixing up an odd-smelling poultice of flour and hydrogen peroxide in the hope of removing a stubborn coffee stain from an island countertop. Spread over the stain, the paste should literally pull the discoloration out of the red travertine. “Granite, marble, and limestone consist of interlocking mineral crystals with pores between them,” he explains. “So spills soak into unprotected stone in just 15 to 20 minutes for granite, and 30 minutes to an hour for marble and limestone.” The liquid evaporates, but a mark remains.

Hueston, who literally wrote the book on the subject of stone restoration (Stain Removal Guide: For Stone, Tile, and Concrete), will leave the poultice in place for 24 hours. This will allow it to “wick” the stain out of the countertop, in the same way that poultices made with other ingredients pull oil stains out of concrete or venom out of snakebite victims. He determines his recipe on the basis of the stain and stone types: an absorbent base like dry clay, flour, or a paper towel, and a wicking chemical such as detergent, bleach, or hydrogen peroxide. If the countertop has been both stained and etched, the stone must be polished and a new sealer applied. “Cleaning spills right away and using coasters is a lot easier,” he says. See all the steps here.

5. Other Kitchen-Counter Hacks: Install Under cabinet Lighting

470_2736533

There’s a missing element in most American kitchens, and it’s not a $7,500 range or a 4-acre refrigerator. No, it’s simply good lighting. And a well-lit kitchen begins with undercabinet task lighting. These hidden fixtures, which are fairly easy to retrofit beneath upper wall cabinets, bathe the countertop in bright white light-a boon for everything from dicing veggies to reading recipes. Connect the fixtures to a dimmer switch, as shown here, and you also have the key to dramatic accent lighting or a night light for midnight snackers.

If you’re a bit tentative about working with electricity, don’t worry. This installation is simple and shock-free, as long as you cut the juice at the breaker box first. Get the rest in How to Install Undercabinet Lighting.

http://www.thisoldhouse.com/toh/kitchen-countertops

plumbing, Plumber

Different Types of Plumbing Repairs

:

Plumbing has grow to be a necessity of today’s everyday life. Living having a clogged sink, bath tub, or toilet isn’t really an choice when you are trying to run a company or take care of a family members. When you have had a pipe burst or a major leak inside your house, you comprehend the importance appropriate plumbing. Here are a few of the most typical plumbing repairs…

A very typical kind of plumbing repair a residence or company may run into is having your water heater fixed. No home would want to go without hot water just like no place of enterprise really should go without having hot water. This is particularly true for the restaurant business that relies on their water heater to wash dishes and keep the place correctly sanitized. Your plumbing professional is capable of fixing any size and brand name water heater that’s out there these days.

Probably the most tough type of plumbing repair is fixing a pipe that has broken. This generally causes extensive damage if not treated fast and effectively. Your plumbing expert can come in and correctly repair the pipe following it has busted. The best factor to do when it occurs would be to turn off the principal water supply to the home or developing to prevent further harm from happening. After the pipe is repaired you are able to your plumber check other pipes for little leaks and signs of damage so that you do not have an additional accident on your hands inside the future.

Numerous expert organizations call for their drains to be properly cleaned multiple times a year. This may aid to help keep a property sanitary, fresh, and aid your entire plumbing system to function the way it was intended to. Having your drains clogged or backed up can trigger an endless amount of harm to your pipes and system. Drain cleaning really should be amongst the normal maintenance and service you’ve carried out at your location of company.

Plumbing Repairs ught to not have to be a headache for a homeowner or company owner. All it takes for your plumbing repairs to obtain done is a call to your trusted and nearby plumbing expert. You are able to expect to obtain a free quote on the work at hand, have the capability to schedule normal maintenance, and can feel confident the repairs will get completed in a timely manner. You need to not let plumbing repairs go untreated for too long simply because all that can cause is much more issues down the road.

plumbing, Plumber

Service Toilet and Repair Instructions

:

Repairing Toilets.
img Most methods of toilet repair are easy do-it-yourself steps. The real challenge of fixing a toilet is usually finding the part causing the problem.

A household toilet should have its own shut-off valve located somewhere near the fixture. Usually, its a chrome-plated compression fitting with an oval knob. So find that before making any repairs.

A tank’s water level should fill to about 1/4″ to 1/2″ below the overflow pipe. Bend the float arm gently to adjust the water level; down to lower the level or up to raise it.

If the arm is hard to bend or needs to be bent a lot, unscrew it first to avoid damaging the ball cock assembly. Also, some assemblies have an adjusting screw on the ball cock valve to regulate the water level.

imgCheck that the flapper (or tank ball) seats properly. Flush the toilet a few times and adjust the flapper until it seats. Adjust its chain connecting to the handle rod if needed.

If the flapper seats correctly, but doesn’t stop water, clean any rust or buildup around the seat opening. If the flapper continues to leak, replace it.

A faulty ball cock valve (the assembly attached to the float arm) may fill the tank and cause water to run continuously down the overflow tube. Always shut off the water supply before removing the valve.

imgSometimes, the ball cock seals can be replaced and the leak will stop. But finding and fixing the problem may not be worthwhile.

It’s often better to buy the whole assembly so you’re sure the leak will be fixed. Or upgrade to an in-line float which seems to operate and adjust a little easier than the arm-type float.

WARNING: It’s easy to crack porcelain when tightening lock nuts so be extra careful when using a wrench. A condition called “back-flow” or “cross-connection” can suck tank water back into the water supply line; contaminating supply water if the ball cock valve is submersed.

plumbing, Plumber

A DAY IN THE LIFE AS A PLUMBER

Link

:

Posted By: Charlotte Plumbing& repair
Sometimes in the plumber profession, things go smoothly, and according to plan. Other times, or rather, MOST of the time, things always seem to go a little sideways. We recently got an email from one of our most frequent and best customers explaining a few minor plumbing jobs that needed to be done on a newly purchased property. On these older homes, it is always a good idea to take a look at them to see what we would be getting in to. The list seemed simple enough- new toilet seat, disconnect gas line to stove and add a shutoff valve, replace kitchen sink and faucet, and replace the bathtub faucet. All of these items were pretty simple on their own, and I had explained that it should be possible to stay within his plumber budget. The next day I started the work and it wasn’t until I headed downstairs that things got interesting. I noticed a few additional problems pretty quickly, such as a rusted-away tub drain and a few water lines that had been split. Even these few problems that were visible where not enough to cause too much concern. I promptly made my way through all of the problems that were noticeable. All of these issues are pretty common with older homes plumber, especially with the old galvanized steel water lines and cast iron drains. When everything APPEARED ok, I slowly started to turn the water on, and this is when the fun began. Within seconds, a slow drip developed, right next to my head. The galvanized pipe was split on the seem on the top of the pipe. Water off, repair made- #1. When that was fixed, it was now time to try again plumbers. I slowly turned the water on, and a little bit further down the line, I see water pouring onto the floor. This time there was a crack in the threaded portion of the pipe. Water off, repair made- #2 plumber. This pattern continued for no less than 6 repairs before I eventually had to call it a day and plan on a round 2 the next day. By the time I was able to get the water on, 75% of the house had been replaced with pex water lines. On day number two I eventually decided to cut my (his) losses and simply start cutting most of the old water lines out plumber. There were a few lines that remained in the walls that were copper, so those remained in tact, even though a few of the fittings had blown apart. What appears to have happened in this house is that it never got properly winterized and literally EVERYTHING froze, EVERYWHERE plumbers. Now that the water was on, I had a slight bit of optimism that I was almost going to be able to get out of there. Of course this was not the case because we are dealing with old plumbing. The toilet would not fill at all due to a completely corroded galvanized line serving it. I had to turn the water back off, and run a new line with a new shutoff valve to the toilet plumber. After the toilet was working, I turned the water on at the dual lavatories and the faucets both worked great, to my surprise! What I was not surprised by though was the fact that the water did not go down the drain AT ALL. After pulling the p traps off both lavs and snaking the main drain serving them, I got all of the water to go where it was supposed to. I was even lucky enough to find a handful of hair ties, straws, toothbrushes, and toys along the way plumber. If you are ever considering purchasing an older home for yourself, to flip or to rent out, keep your plumbing budget plenty high in case of unforeseen problems, which are almost always going to be there. Allow a professional plumber to take care of it for you, and save yourself days, weeks or even a lifetime of Charlotte plumber headaches charlotte plumbing repair.

plumbing, Plumber

The Charlotte Plumber

Link

The CHARLOTTE PLUMBER.

 

The Charlotte Plumber is about providing the best plumbing  jobs, service, list, supplies, plumbing, equipment, plumbers and tools to solve your Charlotte plumbing emergencies for water, get The Charlotte Plumber for CHARLOTTE Plumbing  24/7 Charlotte NC

The Charlotte Plumber | Charlotte Plumber | Plumbing NC: 7 Questions to ask a Charlotte Plumber before buying plumbing suppilies and equipment in Charlotte, Concord, Mooresville, and Ballantyne, NC

Best Charlotte Plumber: The best prices and top things to look for from plumbing suppliers and service contractors.
How an established, recommended and preferred plumbing business can save you money when building or fixing a new house or constructing a new commercial building.

The Charlotte Plumber: A good CHARLOTTE Plumber for a good NC Plumbing  Job is crucial to maximize the efficiency and  power useage of any house or commercial buildding in Charlotte, NC, NORTH CAROLINA…..

Plumber List!

The Charlotte Plumber – NC Plumbing Jobs:  NC Plumber  will  install all the piping and fixtures for a new home which is a crucial aspect of any new building, also the layout and planning of the fixtures, piping and positioning of all the appliances.
Charlotte Plumber jobs : Charlotte Commercial plumber installation jobs for major piping, fixtures and fire protection equipment in commercial and industrial facilities requires dedicated equipment and expert plumbers.

The Charlotte Plumber – Charlotte Plumbing  – Charlotte Plumbing Repairs : All bathrooms, utility rooms, kitchen and landscaping area need to be properly connected in order to have a good functional North Carolina plumbing system.
The CHARLOTTE Plumber – CHARLOTTE Plumbing – CHARLOTTE Plumbing Service: When your plumbing stops working, havoc can occur in your house or business and high priced damage can occur when pipes burst or fixtures have been installed incorrectly.

The Charlotte Plumber – Charlotte Plumber  Emergency: Some emergency plumbing service and situations can be avoided!

Best Charlotte Plumber/Plumbing Emergencies Service: Most plumbers report that negligence is responsible for some items, liquid and solids causing stubborn obstructions in drains and defective pipes that leads to flooding.
Charlotte Plumbing Problem – Plumbing NC: When the faucet starts to drip you should call The NY Plumber, do not waite until you have a plumbing emergency and it is too late to undo the damage done to your home or business.

A Charlotte Plumber can provide general preventive maintenance for the home and business plumbing  every once in a while, it will not only keep plumbing fixtures, drains and pipes in good condition for a long time, but will further allow you to spot early problems and have them fix.

The Charlotte Plumber: Charlotte Plumber is the plumber you call when you encounter an emergency plumbing problem….. you can take steps to reduce damage to the minimum, hence cutting down your plumbing cost.

The Charlotte Plumber: Charlotte  Plumber for Charlotte Plumbing Maintenance and  Charlotte Plumbing Repairs
Charlotte Plumber: The Charlotte Plumber will install and/or repair water heaters, showers, spetic tanks, gas lines oil lines and tanks, boilers, sewers, high pressure cleaning systems, commercial laundry systems, kitchen sinks, gas leaks, water meters, radiators, cloged toilets, jacuzzi, grease traps and more.

Charlotte Plumber: At The Charlotte Plumber you will find professional plumbers or plumbing service contractors to fix your plumbing problems using the best supplies make of brass. copper, plastic or a preferred material, today. Check the at: http://www.charlotteplumbingsvc.com Continue reading The Charlotte Plumber →

plumbing, Plumber

Should I Call a Professional Plumber to Unclog My Drains?

Link

:

Clogged drains are one of the most common questions posed by homeowners, says Charlotte plumbing & repair of Charlotte NC.  It is not advisable to use a chemical drain cleaner in a fixture that is completely blocked.  The most powerful cleaners contain lye, a caustic compound that is dangerous and can harm fixtures if left too long in them.  If the chemical cleaner does not clear the drain, you will be exposed to the caustic when you open a clean-out plug or remove a trap.

There are a couple of variables at play when determining whether you can unclog a toilet yourself or not. The first is the location of the clog. If it is too far down the drain pipe, the only choices may be to use an augur (which most homeowners don’t have – you can rent one or buy one at a hardware store) or to call your local Seattle plumber and get them to hydro jet your system. The second variable is the composition of the actual clog, or if it’s too densely packed, then no amount of do-it-yourself unclogging is going to work.

Charlotte Plumbing & repair Tip of the Week

 Tip # 1  Using a plunger:  Begin by removing the sink strainer or pop-up drain plug.  If there is an overflow opening—most kitchen sinks have none—plug it with wet rags.  Any air gap provided for a dishwasher also must be plugged.  Be sure there is enough water in the basin to cover the plunger cup completely.  Coat the rim of the cup evenly with petroleum jelly and center the cup over the drain hole.  Without breaking the seal between the drain and the cup, pump down and up with short, rapid stroke 10 times, then jerk the plunger up from the drain quickly.

Tip #2  Using an auger:  With the strainer or pop-up stopper removed, feed a drain-and-tap auger into the drain by cranking the handle clockwise.  As you push the auger wire farther into the drain, alternately loosen and tighten the thumbscrew on the auger handle.  When you hook something move the auger backward and forward slowly while cranking, then withdraw the auger wire slowly while continuing to crank in the same direction.  Pour hot water and detergent through the trap to clear away residual grease or oils.

Tip #3  Working through the clean-out plug:  If the trap under the clogged fixture plumbers has a clean-out plug, place a bucket under the trap and remove the plug.  After water has emptied from the trap, straighten a wire coat hanger, form a small hook in one end, and probe through the trap.  If the obstruction is near the opening, you should be able to dislodge it or hook it and draw it out.  If not, feed a drain-and-trap auger first up to the sink opening, then through the back half of the trap. Call http://www.charlotteplumbingsvc.com

plumbing, Plumber

How can I tell if my water and waste pipes are old and corroded?

Link
This article’s intent is to help you diagnose water quality and water pressure along with drainage issues with your potable water and waste pipes. Older homes built before the 1980’s did not have many options as far as plumbing materials go. The most readily available materials were cast iron and galvanized iron pipe. Unfortunately there was not enough technology, research or even thought put into what will happen to these materials down the road. As the result plumbers nationwide have to constantly service and in most cases rip out the entire systems and install new modern systems such as copper, PEX (Polyethylene Cross Linked), ABS, and PVC. If you notice you have slow drains or they do not drain at all, then you may have galvanized iron drains. If you notice low pressure or low flow from your faucets then you may have galvanized iron water lines.
  First of all let’s state the fact that not all iron systems are bad. In fact cast iron drains seem to have an average 40 – 60 year life span. This means if your sewer main is cast iron and has no signs of constant plugging issues or leaks then if it isn’t broke don’t fix it. However, majority of cast systems inside of the building used galvanized drains for all of the branch lines such as tubs, showers, and sinks. Plain and simple, these drains are the worst. Some severe cases will not drain at all and cannot be snaked out. You ask why can’t they be snaked out and I will explain. Modern pipe systems are designed to maintain a smooth path way for fluids and solids. This prevents solids from being caught and eventually blocking the pipe off. Glued fittings such as ABS or PVC, if installed correctly, prevent this from happening. The reason iron does not provide this is simple, it is a corrosive material. Corrosive metals, even treated, will eventually scale and rust from long term exposure to water and chemicals. One other important reason is that it is not maintainable due to original Plumbing contractor error.
  Galvanized drains are threaded pipe turned into the threaded hub of a fitting. If the original installer buried the pipe too deep into the hub you will have a jagged ridge of pipe penetrating into the water way. This is where a service technician will no longer be able to help you. As you push a sewer snake cable into the fitting the end of the cable will bind on that ridge and prevent the cable from passing through the hub. At this point you are out of luck. Last ditch attempt is to use some pure sulfuric acid but that rarely works because there is too much build up. Please note you should never dump sulfuric acid down a disposal because it can severely damage the unit and could blow nasty acid all over you. Please use extreme caution and safety equipment when using such a chemical. Only option left at that point is to remove all of the galvanized drain lines from above the flood level of the fixture in which it serves to the main cast iron trunk line with either ABS or PVC.
  Most all older production homes used galvanized iron water lines. This was at that time period the most common and cost effective way to plumb potable water. If you are lucky the plumbing company

spent a little extra and used copper. If you experience bad water pressure or flow it could be from under sized piping but in most cases it is corroded galvanized pipe. Not only did they almost always under size the system, but the pipes have approximately a 40 year life span depending on your water quality and electrolysis issues. 
  Galvanized water piping will commonly leak at the joints and fittings of a branch arm. This happens because upon installation of the pipe it is thread with a threading machine. When you thread galvanized pipe it removes the galvanized coating at the threads as well as thins the pipe. This is why the most common place for this type of system to leak is at the joints.
  Electrolysis happens when two or more types of metal touch and water flows through them creating an electrical charge that immediately breaks down the softer metal, usually the copper goes first. Finally the most common is natural corrosion. This happens naturally and can be sped up by hard water and other chemicals pumped in by the city’s water supply.
  Once any or all of these things happen the scale inside of the pipe will break off and end up plugging your faucets flow restrictors, faucet aerators, shower cartridges, and shower heads. If you experience any of these symptoms then you probably have this type of pipe and should consider having a licensed Plumber provide you with an estimate to
re-pipe your entire water system charlotte nc.