Tag Archives: Charlotte Plumbing Repair

Plumbing vent types & Terms

Posted by: Charlotte Plumbing & Repair

Vents play a vital component in a home’s drainage program. A faulty venting program will not only trigger aggravation when the drainage system malfunctions, it could also make you and your loved ones ill if it compromises the seal that traps are supposed to maintain against sewer gas. It really is to recognize the various venting choices doable, at the same time as size and installation basics, in the event you program to alter or add your current method.

Venting Types and Terms:
Here are a couple of of essentially the most widespread kinds of events you will uncover within the home.

Vent Terminal: a vent terminal is roughly equivalent to the distance between floors, but as a result of layout considerations, it frequently starts a foot below one floor and ends of foot below the next.
Broken vent: the term broken vent refers to an improperly installed vent that, consistently is ineffective. A broken vent is a small far better than no vent at all.

Stack Vent: vertical drainage stacks are also considered events since furthermore to carrying water, they pull relief air from above the roof. Short horizontal branch lines extending from a vertical stack don’t need extra venting and therefore, are said to be stacked vented.

Vent Stack: a vent stack is a vertical stack installed from the sole purpose of providing relief air. It doesn’t carry water. A vent stack could be tied into the Stack vent above the highest fixture or exit the roof independently.

You may have observed plumbing diagrams within the past with vent stack beginning below the lowest fixture on the stack and continuing into the attic. All fixtures are shown connected to the Stack vent. Nonetheless, dedicated program wide vent stacks are rarely identified in residential installations. They work best in tall commercial buildings

Stack-Vented Branch Arm: in a correctly created method, fixture drain lines are sized so that they are able to by no means run a lot more than one half full. If a horizontal branch pipe isn’t too lengthy unused best half of the pipe can serve as a bank. It feeds air from the stack to the back of the flow, preserving the trap seal. But such a stack prevented branch arm is limited.

The branch need to serve the highest fixture or fix your combination on the stack. This highest fixture rule applies to every individual stack, even when the highest fixture on a second stack is really a floor or two above or below that of the primary stack, supplying that all stacks extend to the open air above the roof. This nevertheless, can have an exception: rules do not apply to a basement bathroom due to the fact most of that piping is horizontal.

The length of the branch should not exceed the limits established by code. The bigger the pipe diameter, the longer the allowed length for the pipe. For instance, most codes specify that 1 a half inch diameter branch arm can extend 5 feet from the stack to the trap, even though numerous further limit that to 3 1/2 feet. Most codes permit 8 feet for it to winch line and 10 feet for 3 inch line. You have to present something longer.

Re-vent: a revamped is really a vent added to a fixture drain when the primary vent is broken in some way. When a branch arm is too lengthy, for instance, when it should step up to accommodate structural barriers, you have to install a re-vent.

Wet and Dry Vents: a wet vent carries water too as air via some component of it piping. A basement bathroom provides a superb example for this simply because the vent for the toilet line also carries water from the tub and laboratory. Although wetlands are handy and efficient, they have their limits. Simply because air ought to share space with water, what vents are low volume vents. They can’t vent many fixtures. The drive vent does not carry water, so it has greater fixture capacity.
Widespread vent: a typical vent is really a single vent pipe that offers relief air to bore fixtures on the single branch line. When you are venting two fixtures on a single branch line, you have to location a typical event between the train outlets. When you are venting far more than to fixtures, install the vent between the last and second to last fixture outlets.

Loop Vent: you need to install a sink in the kitchen island; a conventional vent will not work. In this scenario, a loop vent may be the appropriate kind of vent to use. Loop vents simply handle the low volume fixtures and (like kitchen sinks) which can be installed in island cabinets.

Loop Vents do not extend to open air or tie into stacks or vent stacks. I have no direct, fresh air connections. Rather, and also the volume of air within the piping loop gives the required pressure relief. For this reason, Loop vents are also recognized as barometric vents.

Automatic Event Device: a nonmagnetic device can take the place of a loop vent. It consists of an inverted cup with the spring-loaded diaphragm. This spring permits the piping method to pull air from the cabinet space but keeps gas from escaping. It’s basically a type of check valve, permitting air to flow in only 1 direction.

Although automatic vent devices might be program savers, do not use them where it is feasible to install conventional fence. Since automatic bands have limited capacity, do not use them to vent high-volume drains or to vent much more than 1 fixture. Install them to ensure that they always remain accessible since they can wear out and might want replacing.

Plumbing Repairs

plumbers and heating technicians free ads

Charlotte Plumbing & Repair services to following zip codes

images
Call Charlotte Plumbing & repair for all your residential and commerical plumbing add drain cleaning needs servicing the following areas, 28115,28117,28025,28027,28036,28031,28078,28269,28216,28262,28214,28213,28215,28227,28105,28270,28226,28134,28210,28273,28278,28217,28208,28203,28202,28206,28205,28212,28211,28209,plumbers charlotte nc,plumber charlotte nc

Most common misconceptions about plumbers.

downloadWhat stereotypes come to mind when you think of plumbers? Charlotte Plumbing & Repair plumbers Charlotte NC is not like other companies in the industry. That’s why we’re here to iron out 14 of the most common misconceptions about .

Plumbers make a mess. At Charlotte Plumbing & Repair , this simply isn’t true. We go to such painstaking lengths to respect your home that we actually leave it cleaner than when we found it. For instance, our are careful to park in the street to keep your driveway clear and they never walk on the grass. They even wear shoe covers to prevent tracking anything inside.
Plumbers are not . Perhaps images of smelly, rude, plaid shirt-wearing men are what come to mind when you think of plumbers.Charlotte Plumbing & Repair plumber couldn’t be further from this description. They are clean, polite and wear a professional uniform. You’ve never seen a more professional group of than Charlotte Plumbing & Repair plumbers.
Plumbers charge hefty overtime fees. Have a plumbing emergency? .
Plumbers take their sweet time getting to the residence. We have plumbers on call 24/7 to respond to emergencies in a timely fashion.
Plumbers make up the price as they go along. Our plumbers draw from years of training and experience to produce an accurate estimate before they start on the job. They explain exactly what steps are required for the repair or replacement and how much it will cost so you can decide if you want to go through with it. You’ll always get the price up front, before any work begins.
Plumbers do the work and stick the customer with the bill. Our plumbers keep you informed of any additional problems they find with the or hiccups that may arise during the repair so you’re not left with any unpleasant surprises on the bill.
Plumbers tack on hidden fees. We have clear, upfront pricing and always keep you in the know regarding your plumbing bill. Our plumbers are honest and never overcharge for parts or labor.
Plumbers take their sweet time so they can charge more. Our plumbers arrive promptly and get right to work. They complete the job with the perfect combination of speed and accuracy so the work is completed quickly with no callbacks required.
Plumbers use industry jargon and make the customer feel stupid. Our plumbers want you to understand their process and explain things in layman’s terms to prevent confusion.
Plumbers make far-fetched promises. At Charlotte Plumbing & Repair, we only hire the most professional, experienced plumbers, but even they can’t always work miracles. Our plumbers try their hardest, but they never make a claim unless they can accomplish it.
Plumbers think they know better than the customer. On the contrary, our plumbers know how important it is to ask clarifying questions if they don’t understand the problem. They respect your input and understand that you may have been living with the problem for some time now and therefore understand it well.
Plumbers are loudmouths. If you’ve ever worked with Charlotte Plumbing & Repair plumbers, you know they speak respectfully and calmly without sarcasm or profanity. They never say anything behind your back that they wouldn’t be willing to say to your face.
Plumbers often arrive without the right tools . While it’s true that replacement parts may take time to arrive, every dispatched Charlotte Plumbing & Repair van is equipped to handle any repair, large or small. From indoor faucet leaks to tree roots in your pipes, our plumbers can handle it all. Well-equipped vans prevent trips back and forth and let the job commence without delay.
Plumbers are rude. At Charlotte Plumbing & Repair, courtesy is one of the most important tools we carry. Our plumbers treat you with the respect and chivalry you deserve.

We recognize that exceptional plumbing is about more than clearing the drain clog or fixing the garbage disposal; it’s about assuring that you hired the right company from the moment a Charlotte Plumbing & Repair plumber enters your home. Contact us today to work with a different kind of plumbing company. .
(704) 394-5252.
plumbers charlotte nc, plumber charlotte nc.

Charlotte Plumbing & Repair

Choising the right contractor

(FEE72D11769931286AE8E0A5012B5C90
A problem with the waterheaters in the in the home can lead to significant architectural troubles which explains why having a Charlotte Plumbing contractor on call at any time continues to be a good idea. While the hope is usually that one will never demand the expertise of a Concord Plumbing business, it is best to always be protected than remorseful. Plumbers undertake education and learning to deal with a range of residential plumbing related problems, from your leaking commode to the dripping faucet and a lot more. Do not assume that almost all plumbing contractors are identical, however, as there are many differences in terms of quality and also rates, so you want to ensure you get the best.

You should ask family and friends whom they prefer since they will give you an honest assessment of different businesses contractor. Without having any person in the area you really feel content asking, do some research online seeing as there are many great web pages where evaluations may be read prior to choosing any plumbing contractor. After you have narrowed your own list to a few trained professionals contractor, hunt for assurances and then simply call to obtain estimations. Even though a professional plumbing service will tell you they need to come out and evaluate the trouble right before you’ll get a final price, they ought to be ready to tell you how much you pay for the service call and details of that nature. Last but not least, ensure the plumbing technician has the appropriate bonding and also insurance protection thus, when a problem does indeed arise, the plumbing company is going to be responsible rather than you. You ought to be shielded too while you safeguard the investment in the house repairs. plumbers charlotte nc, plumber charlotte nc.

What to do in a plumbing emergency

plumbers

Charlotte plumber sooner or later most homeowners will experience some type of plumbing emergency. Understanding what to do when a problem occurs will make the emergency much easier to deal with.

First, prepare yourself by locating the water shut-off valve, which is located next to your water meter. Once you have located your water meter, the valve next to it will be the water shut-off valve. By turning off the shut-off valve, you will stop all water from entering your home, thus minimizing water damage.

After you have shut-off the water supply, it is also a good idea to open all sink faucets to drain the water from the pipes to further minimize damage. Then, immediately call a plumber. Reputable, professional plumbers can usually send a technician out in a few hours. Follow any instructions given to you, while you wait for them to arrive.
It is also a good idea to use a mop, rags or paper towels to remove excess water, to help keeping water damage to a minimum.

In the case of overflowing toilets, you can shut-off the toilet water supply valve. This valve can usually be located between the bathroom floor and the toilet tank, on the water line supplying the toilet. If this is your plumbing problem, it is not necessary to shut-off the water to the entire home.

Clogged toilets and sink drains can sometimes be opened with a chemical drain opener. If this does not work, a plunger or snake can be tried to remove the clog. If these methods fail to open the clogged drain, you will need to call a plumber.

If it is a water heater problem, immediately shut the unit off. It is a good idea to locate the electrical shut-off switch beforehand. Also be sure to keep the telephone number of a licensed, professional plumber, with emergency services, handy. Handling a plumbing emergency can be made much easier, by following the steps above.

Are you facing a plumbing emergency in the Charlotte,Lake Norman area? Stop and call Charlotte Plumbing & Repair immediately at (704) 394-5252.

Leak Detection & Emergency Plumbing

Charlotte Temperatures Will Soon Plummet — Frozen Pipes Are A Real Possibility

insulated-pipes3

Charlotte doesn’t tend to get as cold as cities to the north, but temperatures can plummet below 20 degrees, and a storm can bring on a power outage. It’s wise to be mindful of what can do to your home. Frozen pipes, for example, are a real possibility.

You want to avoid this at all costs, as a pipe can burst and create a very messy situation.

Homes built as recently as the 1970s frequently lack sufficient wall insulation. This means that if a kitchen or bathroom sink is along an exterior wall, your plumbing could be exposed to more cold than it should be. As precautionary measures:

Insulate your pipes. Home improvement stores carry a range of plumbing-line insulation. Your options include foil and fiberglass. Perhaps the easiest option is tubular insulation, which can be cut to measure and wrapped around a pipe. All of these supplies are available at home-improvement stores.
Seal the gaps around the plumbing lines coming into your home. Expanding-foam should do the job.
You may even want to talk with your plumbing contractor about relocating your pipes, especially if they’ve locked up before. This tends to be an expensive alternative, but it may be worth discussing with your plumber.
If temperatures plummet before you can do your preventive maintenance, take the following measures:

Let your faucets slowly drip. This will help to prevent a freeze-up.
Open the cabinets under your sink. This will allow warmer air from the room to circulate under the sink.
If a pipe does freeze, try using a hair blower or a heating pad to thaw it. Never use a blow torch or any other flame. A better approach is who can get the pipe thawed before it bursts. The pipe, by the way, isn’t likely to burst where it’s frozen, but instead at a point between the ice and the faucet.
If you plan to be away for an extended time during the holidays, consider draining your system before you leave. Turn off the main valve, and let all the faucets run until no more water comes out. This should prevent a freeze-up while you’re gone.

At Charlotte Plumbing & Repair we know how important it is to keep your water lines maintained. We can help you do that, whether it’s winter or summer. Call us with any questions. We’re happy to help.

TANKLESS IN CHARLOTTE, Water Heaters

d205e13d-cbb0-4d28-bf74-242cbcc30390_1000

You can find a good-sized tank heater for a decent price in many places, but these inexpensive heaters may not always be the bargain they seem to be.

These are typically in the 40-50 gallon range, and they will heat water so that you have that many gallons available when you need to wash dishes, take a shower, wash the dog, or whatever.

The tank unit works by warming that amount of water and then holding it ready, just in case you need it. This means the water is kept at a steady 160 degrees (or whatever temperature you set it to), at all times of day.

The heater thus is going on and off all day and all night to keep the water hot. Your Charlotte electric bill reflects this.

It sounds like that cheap water heater may not be so cheap, doesn’t it? Yikes!

Hot Water Loss and Limited Supply

Traditional tank heaters lose heat steadily. As the tank stands full with hot water, that warmth is lost through heat that basically seeps away. Picture a tea or coffee mug. As the tea or coffee cools, that heat is lost.

Even though your heater is insulated, there is still significant heat lost as it radiates away. That heat loss can be as much as 20 to 40%.

Another drawback of traditional “cheap” water heaters is that the hot water can get used up. If one person takes a shower, he may actually use up all the water that is hot. Then the next person needs to wait 30-60 minutes to get hot shower.

What a drag!

An Efficient Alternative to Cheap Water Heaters

Consider a Tankless Heater.

You may also have heard of these called “point-of-use” heaters, “on-demand” heaters, or “electric instant hot water heaters.”

What this means is that the heater provides hot water when you need it.

There is no water stored. When you turn on the hot faucet, the on-demand heater warms up the water so you can take a shower for as long as you want, and then lets the next person shower, too – all without running out of hot water.

Why is this a better alternative to the cheap tank heaters you find at your Charlotte home improvement store?

Quite simply, cheap water heaters do not prove to be cheap in the long run.

Benefits of “Cheap Water Heaters”

You may want to reconsider what you think a cheap water heater is, since the research has shown that what may have been the cheap heater initially may not be the cheap heater in the long run.

Point-of-use tank heaters can be initially more expensive. However, think about this: Point-of-use heaters can save as much as 50% over your current heating expenses! An on-demand heater will only provide hot water when you need it, so there is no need to continue to heat water if you aren’t using it. No more day-and-night heating bills.

On-demand heaters are also cheap heaters because they don’t wear out like traditional tank units. Traditional units have a typical life of 6 to 12 years before needing to be replaced.

A tankless water heater can last 20 years and more, since they don’t have hot water “sitting” in the tank and corroding internal parts. Hard water scale and deposits can greatly reduce the life and efficiency of a tank heater.

Tankless heaters are also space-efficient. They take up a lot less room in your Charlotte home than their traditional counterparts. Imagine having your water heater hang on the wall, taking up only as much space as a briefcase!

One other benefit of this type of cheap water heater is their safety record. Traditional tank heaters require you to set a minimum temperature, which is often much higher than you really need. Point-of-use heaters allow you to set the temperature where you will use it, preventing scalding issues and more energy loss.

So what do you think? Which is really the cheap water heater?

You may find it helpful to consult your Charlotte Plumber. who can provide you with extensive information about tankless water heaters, and when you’ve reached your decision, safely and efficiently install your water heater.

Charlotte Plumbers, Charlotte NC

The Charlotte Plumbers is about providing the best plumbing jobs, service, list, supplies, plumbing, equipment, plumbers and tools to solve your Charlotte plumbing emergencies for water, get The Charlotte Plumbers for CHARLOTTE Plumbing 24/7 Charlotte NC

The Charlotte Plumbers | Charlotte Plumbers NC | Plumbing NC: 7 Questions to ask a Charlotte Plumbers before buying plumbing supplies and equipment in Charlotte, Concord, Mooresville, and Ballantyne, NC

Best Charlotte Plumbers: The best prices and top things to look for from plumbing suppliers and service contractors.
How an established, recommended and preferred plumbing business can save you money when building or fixing a new house or constructing a new commercial building.

The Charlotte Plumbers: A good CHARLOTTE Plumbers for a good NC Plumbing Job is crucial to maximize the efficiency and power usage of any house or commercial building in Charlotte, NC, NORTH CAROLINA…..plumbers charlotte nc.

Plumbers List!

The Charlotte Plumbers – NC Plumbing Jobs: NC Plumbers will install all the piping and fixtures for a new home which is a crucial aspect of any new building, also the layout and planning of the fixtures, piping and positioning of all the appliances.
Charlotte Plumbers jobs : Charlotte Commercial plumbers installation jobs for major piping, fixtures and fire protection equipment in commercial and industrial facilities requires dedicated equipment and expert plumbers. plumber charlotte nc

The Charlotte Plumbers – Charlotte Plumbing – Charlotte Plumbing Repairs : All bathrooms, utility rooms, kitchen and landscaping area need to be properly connected in order to have a good functional North Carolina plumbing system.
The CHARLOTTE Plumbers – CHARLOTTE Plumbing – CHARLOTTE Plumbing Service: When your plumbing stops working, havoc can occur in your house or business and high priced damage can occur when pipes burst or fixtures have been installed incorrectly.

The Charlotte Plumbers – Charlotte Plumber Emergency: Some emergency plumbing service and situations can be avoided!

Best Charlotte Plumbers/Plumbing Emergencies Service: Most plumbers report that negligence is responsible for some items, liquid and solids causing stubborn obstructions in drains and defective pipes that leads to flooding.
Charlotte Plumbing Problem – Plumbing NC: When the faucet starts to drip you should call The Charlotte Plumber, do not Waite until you have a plumbing emergency and it is too late to undo the damage done to your home or business.

A Charlotte Plumber can provide general preventive maintenance for the home and business plumbing every once in a while, it will not only keep plumbing fixtures, drains and pipes in good condition for a long time, but will further allow you to spot early problems and have them fix.

The Charlotte Plumbers: Charlotte Plumbers is the plumber you call when you encounter an emergency plumbing problem….. you can take steps to reduce damage to the minimum, hence cutting down your plumbing cost.

The Charlotte Plumbers: Charlotte Plumbers for Charlotte Plumbing Maintenance and Charlotte Plumbing Repairs
Charlotte Plumbers: The Charlotte Plumber will install and/or repair water heaters, showers, septic tanks, gas lines oil lines and tanks, boilers, sewers, high pressure cleaning systems, commercial laundry systems, kitchen sinks, gas leaks, water meters, radiators, clogged toilets, Jacuzzi, grease traps and more.

Charlotte Plumbers: At The Charlotte Plumbers NC you will find professional plumbers or plumbing service contractors to fix your plumbing problems using the best supplies make of brass. copper, plastic or a preferred material, today. Check the at: http://www.charlotteplumbingsvc.com

The Charlotte Plumbers: At Charlotte you get houses for sale and homes for sale or rent. Choose the best house for sale by owner, painter, furniture, products and appliances discounts.

The Charlotte Plumbers – Charlotte House List: Plumbing and Home Improvement Supplies can be found in Charlotte North Carolina NC at: http://www.charlotteplumbingsvc.com

Different Types of Plumbing Repairs

:

Plumbing has grow to be a necessity of today’s everyday life. Living having a clogged sink, bath tub, or toilet isn’t really an choice when you are trying to run a company or take care of a family members. When you have had a pipe burst or a major leak inside your house, you comprehend the importance appropriate plumbing. Here are a few of the most typical plumbing repairs…

A very typical kind of plumbing repair a residence or company may run into is having your water heater fixed. No home would want to go without hot water just like no place of enterprise really should go without having hot water. This is particularly true for the restaurant business that relies on their water heater to wash dishes and keep the place correctly sanitized. Your plumbing professional is capable of fixing any size and brand name water heater that’s out there these days.

Probably the most tough type of plumbing repair is fixing a pipe that has broken. This generally causes extensive damage if not treated fast and effectively. Your plumbing expert can come in and correctly repair the pipe following it has busted. The best factor to do when it occurs would be to turn off the principal water supply to the home or developing to prevent further harm from happening. After the pipe is repaired you are able to your plumber check other pipes for little leaks and signs of damage so that you do not have an additional accident on your hands inside the future.

Numerous expert organizations call for their drains to be properly cleaned multiple times a year. This may aid to help keep a property sanitary, fresh, and aid your entire plumbing system to function the way it was intended to. Having your drains clogged or backed up can trigger an endless amount of harm to your pipes and system. Drain cleaning really should be amongst the normal maintenance and service you’ve carried out at your location of company.

Plumbing Repairs ught to not have to be a headache for a homeowner or company owner. All it takes for your plumbing repairs to obtain done is a call to your trusted and nearby plumbing expert. You are able to expect to obtain a free quote on the work at hand, have the capability to schedule normal maintenance, and can feel confident the repairs will get completed in a timely manner. You need to not let plumbing repairs go untreated for too long simply because all that can cause is much more issues down the road.

Service Toilet and Repair Instructions

:

Repairing Toilets.
img Most methods of toilet repair are easy do-it-yourself steps. The real challenge of fixing a toilet is usually finding the part causing the problem.

A household toilet should have its own shut-off valve located somewhere near the fixture. Usually, its a chrome-plated compression fitting with an oval knob. So find that before making any repairs.

A tank’s water level should fill to about 1/4″ to 1/2″ below the overflow pipe. Bend the float arm gently to adjust the water level; down to lower the level or up to raise it.

If the arm is hard to bend or needs to be bent a lot, unscrew it first to avoid damaging the ball cock assembly. Also, some assemblies have an adjusting screw on the ball cock valve to regulate the water level.

imgCheck that the flapper (or tank ball) seats properly. Flush the toilet a few times and adjust the flapper until it seats. Adjust its chain connecting to the handle rod if needed.

If the flapper seats correctly, but doesn’t stop water, clean any rust or buildup around the seat opening. If the flapper continues to leak, replace it.

A faulty ball cock valve (the assembly attached to the float arm) may fill the tank and cause water to run continuously down the overflow tube. Always shut off the water supply before removing the valve.

imgSometimes, the ball cock seals can be replaced and the leak will stop. But finding and fixing the problem may not be worthwhile.

It’s often better to buy the whole assembly so you’re sure the leak will be fixed. Or upgrade to an in-line float which seems to operate and adjust a little easier than the arm-type float.

WARNING: It’s easy to crack porcelain when tightening lock nuts so be extra careful when using a wrench. A condition called “back-flow” or “cross-connection” can suck tank water back into the water supply line; contaminating supply water if the ball cock valve is submersed.