Tag Archives: toilet repair

Plumbing

How to Replace a Toilet

You might be amazed by the amount of money you can save on your next water bill by replacing your toilet with a new 1.6 gal per flush water saving unit. This is a job that can be completed by the general homeowner in an afternoon. With sufficient preparation, replacing a toilet is a fairly straight forward task.
Step 1:
Remove the new 1.6 toilet from its box and make sure there is no chips or scratches. Verify that all the parts are there. You will also need a wax ring which should come with the new toilet.

Step 2:
Turn off the water behind the toilet and flush the toilet to drain it. You will need to soak up as much as you can with a shop vac or rag and wring it into a pal. A genereal pair of rubber gloves will be helpful for the next step.

Step 3:
Separate the tank from the bowl by loosening the tank bolts. Take the tank off the bowl and discard it.

Step 4:
Unscrew the floor bolts that hold the base to the floor. Use a pair of pliers if the bolts are hard to move. Gently rock the toilet base to break the wax seal.

Step 5:
Lift the toilet straight up and set it on a piece of the box in order to protect the floor from any remaining water in the bowl or wax from the bottom. The cardboard will make it easier to move the toilet out of the way. It is a good idea to cover up the pipe with an old rag or plastic bag to prevent sewer gasses from escaping.

Step 6:
Remove the wax seal with a putty knife or paper towels. Apply the new wax seal around the toilet flange. first remember to remove the rag from the drain pipe.

Step 7:
Apply the new wax seal. Place the new toilet base over the floor bolts and center it over the wax seal. Tighten the bolts but not to tight and replace the caps. Attach the tank to the new base with the included hardware.

Step 8:
Connect a new water line to the toilet. Turn the water back on and wait for the tank to fill and check for leaks. You will need to flush a couple of times to fill the bowl with water.toilet

plumbing, Plumber

How to Locate Water Leaks With Leak Detection

Leaking toilets, leaky pipes,leak detection, drippy faucets and Slab leaks are familiar plumbing emergencies that waste lots of water and millions of dollars in structural destruction. Fast leak detection saves a lot of water as-well-as high-priced repairs of defective ceilings, walls and floors.

Inadequate workmanship or low-grade installation of pipelines may give rise to domestic and industrial plumbing water seepage’s. Plumbing contractors single out leaks on regular plumbing maintenance to faucets, drains, toilets, bathtubs and sinks as a probable explanation for the development of water seepages. Rusted pipes, worn out valves and detached connections are accountable for water seepages.

Roughly 1 in each and every three hundred homes and constructed dwellings is at this moment dealing with water leakage. 1/8″ pit in pipe seeps out 2500 gallons in twenty four hours. A runny toilet can use up too 90,000 gallons in under a month. A drippy faucet or a oozy garden hose can waste close to one hundred and eighty gallons on a monthly basis and 2160 gallons per year.

Water leaks give off symptoms that can’t be ignored. Different water meter readings, sewer gas smells, high water bills, waterlogged patches, recurring sewer backwashes, and fungus are indicators of water seepages inside or outside your home. Taking action on the above mentioned symptoms will be sufficient at reducing water destruction. Switch off the main water supply to the home to stop water seepage. Contact a plumbing service provider for early on leak diagnosis and express repair leak detection.

1 in twenty pools spills water. Swimming pool water leaks are money and water guzzlers. A broken swimming pool shell, loose tiles, strange growth of grass or a loss of 0.125 inches of water in one day are obvious signals for swimming pool water leaks. Don’t delay fixing once those hints emerge. Call a leak detection service provider before additional ruin arises.

Plumbers carry above ground leak detection and underground slab leak detectors (plumbing services)slab leak repair

plumber charlotte nc, plumbers charlotte nc, Plumbing, plumbing, Plumber

Common Toilet problems/ Charlotte Plumbers Blog.

2889.216.020

Are you experiencing issues with your toilet? If so, we hope you find this Toilet Troubleshooting guide useful. Please remember that it’s often more economical to call a Licensed Charlotte Plumber, like Charlotte Plumbing & Repair to troubleshoot and fix your plumbing issues. Our number is (704)394-5252, and we have technicians standing by, 24 hours a day, 7 days a week.

As folks retire for the evening to sleep, water pressure in municipal water systems begins to rise. This increase in stress can be transferred to a worn ball cock valve and trigger it to vibrate ever so slightly. This is the moaning you are hearing. Get a new valve.

Ghost Flushing

Does your toilet tank start to fill on its own? In other words, run for an extra five or 10 seconds? This is usually due to the following causes: poorly fitting/leaking flapper and/or a refill tube that is too long. A worn flapper or corroded flapper seat will trigger water to slowly drain from the tank into the toilet bowl. After an hour or two the water level drops enough and the fill valve kicks on. The same thing can happen if the water line that runs from the base of the fill valve to the inside of the overflow tube is simply too long. This may siphon water from the tank. New fill valves come with a special clip that holds the tip of the water line up and ensures that water will stay in the tank where it belongs.

Multiple Flushes

Do you flush your toilet and get two for the value of 1? If that’s the case, the water level within the tank could also be too high. Alter the float management on the fill valve and try to drop the water level in the bathroom tank one inch or so. Trial and error will let you get the water level correct.

Partial Flushes

You flush the toilet and get cheated. The flapper valve can get waterlogged over time and flop down too quickly. The chain that connects between the flapper valve and the flush handle could also be too tight. Adjust it one link at a time. The water level in the toilet tank could also be too low. Modify the fill valve so that extra water enters the tank. You may have a primary era low flush toilet. If so, you are toast! These toilets have basic design flaws. They simply don’t have sufficient power to flush the bathroom bowl correctly. In case you have one in every of these 1.6 gallon flush nightmares, hold on, help may be on the way. It appears that the 1992 legislation requiring these bad boys could be repealed. If this happens, 3.5 gallon toilets could come back.

Whistle While it Works

As the toilet tank fills and is sort of finished, it makes all sorts of excessive pitched noise, right? You most likely have an old fashioned ball cock fill valve with a float ball on an arm. These valves close slowly as the water stage rises and the valve begins to vibrate as this happens. The answer is a brand new fill valve. These new valves stay open completely till the bathroom tank is filled. The shut off is instantaneous.

Tough Toilet Bowl Stains

Do you have stains in your toilet bowl that just won’t budge? If so, DON’T use abrasive cleaners! Use white vinegar or muriatic acid to wash the bowl. White vinegar is safer, but takes longer. Muriatic acid can clean a toilet bowl inside minutes. Be careful!

Toilet Bowl Water Level Drops

After you walk away from the toilet, does the water degree mysteriously drop? If that’s the case, two things could be wrong. The toilet could be partially clogged. The clog can cause a siphon and pull water from the bowl. The other possibility is more severe: there could be a crack or small defect within the colon of the toilet. That is the channel that water passes by means of to get to the drain pipe. A colon crack or defect means it is time for a new toilet.

Low Energy Flushes

The water release holes within the lip of the bowl my be clogged with water deposits. Pour a quart of muriatic acid down the overflow tube in the tank to clean these holes. You should hear a sizzling sound if the deposits are heavy. The acid will not hurt the toilet. It’s also possible to attempt to open these holes with a toothpick should you do not have acid.

Shaking Toilet

Does your toilet rock whenever you sit on it? If so, the grout between the toilet and the ground must be replaced. Grout must be used as an alternative of caulk. Caulk is flexible and will allow toilet movement.

Water Leaks at Base of Toilet

In the event you see water leaking around the base of the bathroom or in the room below when it’s flushed, the wax gasket between the toilet and the drain pipe flange has to be changed. This is not a DIY friendly activity although the TV exhibits make it seem so! For those who tackle this, be sure to have access to a different toilet as you could be opening a can of worms! Contact Us and let Legacy Plumbing Company, your Raleigh Plumber fix this.

Save Water With Brick?

Putting in brick in a toilet tank to displace water could assist save a little bit water, however it usually causes more problems. Drop one while putting in it, and you could crack the tank. The brick also can interfere with the operation of the shifting elements in the tank, and cause less powerful flushes, resulting in more water being used.

Gradual or Noisy Refill Water Stream

If the water entering the toilet enters slowly, the shut off valve may be only partially open. Test to verify this valve is open all of the way. If water rushes into a toilet tank too quickly, close the valve so that the water flows in a more controlled fashion.

Still having problems with your toilet? Charlotte plumbing repair technicians are available 24 hours a day in Charlotte metro area. Simply call Charlotte Plumbing & Repair at (704)394-5252 or Contact Us, and we will call and schedule an appointment with you.
1025 w trade st
Charlotte, NC 28202